how to install a washing machine drain hose

Take the new hose and slide the clamp on. We will install the part in the same order as we removed it.

Washing Machine Drain Hose Installation Tutorial

Home To Any Budget Home To Any Possibility.

. Get Free Quotes Fast. After that secure the drain hose with a hose clamp about 15 cm or 6 inches down into the drain pipe. The first step is to turn off the power to the washer and wait five minutes for the liquid and gas lines to cool down.

With a hose clamp we attach the hose to the pump. You simply have to unscrew each clamp then pull the hose pipe off the washing machine. Now place the hose onto the connector located at the back of the washing machine and slide the clamp to where the hose rests on the connector.

Ad Get Fast Quotes and Great Service. Featured Shops Back to School Teachers Shop Back to College American Jobs Black Unlimited Built for Better Best Sellers. Use a pair of pliers take the clamp and remove it from the old hose.

Follow the below steps to install a waste pipe for the washing machine. With a wrench make the hold of the clamp tight. Turn Off the Washer and Locate the Drain Line.

Check that the washing machine is draining properly to extract adequate water from the load. It should go through the straight end. There should be no leaks around the edges of the hose.

Insert the end of the drain hose into the standpipe. Next Locate the washing machine drain line. Washing Machine Drain Hose Installation Tutorial Whirlpool Self Help Videos.

Ad Lowes Has Your Next Project Covered. Remove any dirt off them using a damp cloth. If the drain is built into the wall fasten the drain hose to one of the water inlet hoses with a tie strap.

After unplug the machines electrical cord from the outlet. The drain hose assembly shown in this video is Part DC97-16979A PD00011192 but the instructions in the. Install the new drain pipe.

Make sure you turn off both the hot and cold water that leads to the old machine before disconnecting it. Proper installation method and location of th. For Front Load washers the drain hose should be no more than 7 down into the drain pipe.

Top Rated Handyman Service. Top Rated Handyman Service. Remove the part and loosen the clamp designed to connect the pump to the hose.

Up to 7 cash back Savings Featured Shops. The second end also needs to be disconnected. Make sure it fits properly so that you will have no problems with leakage.

DO NOT install the end of the drain hose higher than 96 inches above the bottom of the washer. Write down the Appliance Specifications After you have gotten the hose on your machine you can plug it back in and turn on the water. Open up the water to see how it flows through the tube.

Deals Shop All Deals Flash Picks Rollbacks Clearance. The drain plumbing needs to be at least 30 high to be sure that no water will be sucked from it. Errors in installation and operation can lead to Because the drain hose is located too low the water flows by gravity into the drain.

Connect the water supply hose. Slide it up on the hose a bit. This can be found on the exterior of the machine or.

Place the bent end of the drain hose into the drain pipe if its close to a wall. The washing machine can hang for a number of reasons. Release the drain pump.

The water supply hose is what feeds water into your washing machine when you do laundry. You may need pliers or a wrench to disconnect stuck on hoses attached to the old washing machine. Whether installing reinforced rubber or steel braided washing machine hoses these are the steps necessary to install your new washing machine hoses.

To do this unscrew the bolts. Youll need a masonry bit and anchor to get through it if youre working with concrete. Next you can then screw the clamp into the nearest wall stud.

Take a new hose. Twist that hose to pull it off of the pump. What is the correct height for a washing machine drain.

Learn how to install a GE Appliances Washer Drain Hose. How to Install Washing Machine Hoses. Use a tie strap to secure the drain hose in place.

If they are rusty and. Discard the old hose. Step-by-step instructions on how to replace the drain hose on a Samsung washing machine.

At this point you should be well aware of how to install a washing machine drain hose. Make Your Plumbing Project A Success At Lowes. Use a pair of pliers and simply squeeze on the spring clamp that holds the drain hose to the drain pump.

Before touching the hoses turn off your washing machine by cutting the power at the breaker box. Knowledgeable Associates Here To Help. Once you have the old hose pipe unhooked ensure that your clumps are in the right condition.

Draining Laundry Sink Into Washer Stack